Runco CR-32HD User Manual

OW N E R ’S OP E R A T I N G MA N U A LCR-32HD / CR-40HDwithCrystal Series™ LCD Displays

10Control PanelsCR-32HD Rear View and Input PanelINPUT2 S-Video InputINPUT2 Audio InputINPUT2 Video InputHeadphone JackRGB Input Connector (PC)DVI-D I

11Control PanelsCR-40HD Rear View and Input PanelBottom Side13 14 1510119875 6121617181920 21INPUT4INPUT3INPUT1MONITOR-OUTINPUT2 S-Video InputINPUT2 A

12Note:• Makes sure there are no objects between the remote control and its sensor.• Don’t place the remote control near a heater or in damp pl

13To view television channels, a signal must be input from either an outdoor antenna or a cable television system.1. Connect the antenna or in

14Using the MONITOR OUT featureConnecting to a DVD or DTV Set-Top Box INPUT (RCA or DVI)ConnectionsINPUT4INPUT31. Connect the video cables to the Y,

15Connecting to a PCConnectionsTo use the display as a PC Monitor1. Turn the PC on.2. Depending on the connection, press the DVI or RGB HD button

161. First, click on Settings on the Windows Start menu and click on “Control Panel”.2. Double click on the Display icon.3. Click on the Settings tab

17Connecting the Power Cord and Switching the Display On / Off4 501001 236TIMEROFFINPUT17 8 9OFF ONINPUT2INPUT3INPUT4SOURCE1. Connect the power cord

18Selecting an Aspect RatioBasic Operations1. Press the MENU button on the remote control.2. Press the ▲▼ buttons to select Aspect Ratio and then pr

19Selecting Picture Adjust1. Press the MENU button on the remote control.2. Press the ▲▼ button to select PICTURE ADJUST and then press the ENTER or

Table of ContentsOne Year Limited Warranty ...4Introduction ...

20Equalizer1. Press the ▲▼ buttons to select Equalizer and then press the ENTER or ► button.2. Press the ▲▼ buttons to select Standard, Music, Film, S

21Selecting Timer1. Press the MENU button on the remote control.2. Press the ▲▼ buttons to select Timer and then press the ENTER or ► button.3. Pres

221. Press the MENU button on the remote control.2. Press the ▲▼ buttons to select Setup and then press the ENTER or ► button.3. Press the ▲▼ buttons

23Setup1. Press the ▲▼ buttons to select Parental Control and then press the ENTER or ► button.2. Enter your 4-digit PIN number to access the Par

24SetupMonitor OutOverscanInput Selection1. Press the ▲▼ buttons to select Input Selection and then press the ENTER or ► button.2. Press the ▲▼ b

25ISF CalibrationTo be used by a Runco Service Technician or an ISF Certified personnel. A pass code is required to access the ISF Calibra

26ISF Calibration (Service)Blue EnableISF Calibration Picture Adjust White Balance Blue Enable DNR Gamma Baud Rate Command Ack Factory

27Displaying the Picture in Picture (PIP)1. Press the PIP ( ) button. There are 2 modes of PIP window : Small, Twin. Whenever you press th

281. Press the () button on the remote control. • When you are viewing the Sub-picture : The sub picture size will be changed in the following

29Swapping the Main & Sub-PictureSwapping the Main & Sub-SoundPicture in Picture (PIP)1. Press the ( ) button on the remote control. • The Ma

3ISF Calibration (Service)Picture Adjust ...

30Changing the PIP Aspect RatioPicture in Picture (PIP)1. Press the ( ) button on the remote control. • When you are viewing the Main image: The i

31Listening to Stereo Sound / SAPDepending on the particular program being broadcast, you can listen to stereo, mono, or a Secondary Audio Program

32RS-232C ConfigurationsRS-232 ConfigurationsNote: • All commands are in ASCII format • Default baud rate is 115200,8,N,1, but can be changed (see p

33RS-232 Configurations‘[‘ + ‘S3A’ + ‘000#’ Set audio volume to ### (=000~100)Example: [ S3A000075 sets volume to 75‘[‘ + ‘+3A’ Audio volume up‘[‘ +

34RS-232 ConfigurationsThe following serial commands are meant to emulate buttons on the remote control. Each button has its own serial command, so ef

35If the signal from the system equals the standard signal mode, the screen will adjust automatically. If the signal from the system does not equal th

36PC Input Connector (D-Sub 15Pin)DVI-D Connector Pin PC INPin PC IN1 Red (R)8Blue (B) Ground2 Green (G)9 Reserved3 Blue (B)10Sync Ground4 Ground11Gro

37For Display PanelTroubleshootingNo picture or sound.• Make sure the display is plugged in.• Make sure the power cord is connected correctly.• Check

38“No signal” message• Check if the signal cable (DVI Cable) is properly connected to the computer. (See page 15)“Out of range” message• This messag

39SpecificationsCR-32HD CR-40HDNative Resolution: 1366 x 768 WXGA 1366 x 768 WXGAScreen Size:32 in. (diagonal) 40 in. (diagonal)Screen Aspect Ratio:16

One Year Limited Warranty4Congratulations on your purchase of Runco’s latest video product and welcome to the Runco family! We believe Runco produces

40Dimensions40 in. (1016 mm)45.75 in. (1162 mm)39 in. (991 mm)9.85 in. (250 mm)25.125 in.(638 mm)23.5 in.(597 mm)4.5 in. (114.3 mm)CR-40HDCR-32HD32 in

Runco International • 2900 Faber Street • Union City, CA 94587 • Ph (510) 324-7777 / (800) 23RUNCO / Fax (510) 324-9300www.runco.comRUMA-0110957-13-05

5This Limited Warranty only covers failure due to defects in materials and workmanship that occur during normal use and does not cover normal maintena

6RUNCO VIDEO PRODUCT INFORMATION RETAIN THIS INFORMATION FOR YOUR RECORDS Model Purchased Date

7Runco presents the high performance Crystal Series™ LCD displays, perfect for those who demand our award-winning flat panel performance in more intim

8CAUTIONTo turn off main power, be sure to remove the plugs from power outlets. The power outlet socket should be installed as near to the equipment a

9CR-32HD and CR-40HD Front View1 TV/AV Button (Input Source Selection)2 MENU Selection Button3 Volume Adjustment Buttons4 Channel Selection Buttons5 R