Runco D-73d Ultra Specifications Page 116
- Page / 152
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Maintenance and Troubleshooting
100 D-73d Series Installation/Operation Manual
Identifying the Left and Right Polarizers: Although the left and right polarizers have
very different optical characteristics, they appear to be identical. As a result, once you
remove them from the projector it may be difficult to tell them apart. Use the following
technique to verify which one is which:
1. Place the polarizer on a clean, smooth, flat surface with the side that faces the
projector facing up.
2. Hold a pair of 3D glasses above the polarizer as shown here:
3. If the right lens on the glasses turns black when it is above the polarizer, this tells you
that the polarizer came from the left-eye optical engine on the projector.
Troubleshooting Table 5-1 provides some general guidelines for troubleshooting problems you may
encounter with the D-73d Series LED 3-D Home Theater Projection System. If the
suggested solutions fail to resolve the problem or if you encounter an issue not
described here, please contact your Runco dealer or Runco Technical Support.
572-2479-00REV00 572-2479-00REV00
Left Polarizer* Left Polarizer*
* viewed from the side facing the projector
3D Glasses
L R
L R
Same Angle of
Polarization
(light passes)
Different Angles
of Polarization
(light does
not pass)
➤
Table 5-1. Troubleshooting Chart
Symptom Possible Cause(s) Solution
The projector does not turn
on.
• The projector is not
plugged in or the AC outlet
is not active.
• The Dimension Digital
Controller is not plugged in
or the AC outlet is not
active.
• The remote control
batteries have run out.
• Ensure that the projector is
plugged in and that the AC
outlet is active.
• Ensure that the Dimension
Digital Controller is
plugged in and that the AC
outlet is active.
• Replace the batteries.
The “left-eye” optical engine
does not turn on or respond
to user commands. The vac-
uum fluorescent display on
the Dimension Digital Control-
ler front panel displays the fol-
lowing message:
Primary Display Error
Communication Failure
• The serial connection from
the Dimension Digital
Controller to the “left-eye”
optical engine on the
display is incorrect or the
cable is faulty.
• Ensure that the
Pri Display Control
(RS-232) output from the
Dimension Digital
Controller is properly
connected to the display
(see Figure 3-14).
- 3Dimension™ Series 1
- Warranty 3
- Important Safety Instructions 7
- Compliance Information 9
- Table of Contents 11
- List of Figures 15
- 1. Introduction 17
- Using This Manual 18
- Description, Features 19
- Introduction 20
- 2. System Overview 23
- Projector 24
- System Overview 25
- D-73d Remote Control 31
- 3. Installation 37
- Quick Setup 38
- Installation 39
- Considerations 39
- Estimating Throw Distance 40
- Throw Distance (TD) = 40
- Screen width (w) 40
- Ceiling Installation 42
- Floor Installation 42
- 3.0 in. (76.2 mm) 46
- Clearance 46
- Installing the 47
- Optional Anamorphic 47
- Lens Mount 47
- Mounting the D-73d 52
- Mounting the 53
- Interconnections 54
- SECONDARY 55
- Audio Processor/ 56
- Switcher 56
- Secondary Display 56
- Control System 57
- AutoScope Lens Motor 58
- Notebook Computer 61
- HDMI source 62
- COMPONEN T 63
- VIDEO OUT 63
- RGB Camcorder 64
- Gaming Console 65
- DVD/DTV STB 65
- Power-Up Sequence 67
- Alignment Procedure 67
- 16:9 1080i/60 70
- Correct Lens Angle 76
- Incorrect Lens Angle 76
- Wrong Position 77
- Correct Position 77
- Vertical Keystoning 78
- Horizontal Keystoning 78
- Pincushion Distortion 78
- 4. Operation 81
- 4:3 Image on 84
- 16:9 Screen (Display) 84
- 16:9 Display 85
- (Letterbox aspect ratio) 85
- 1080i HDTV Image 86
- 720p HDTV Image 86
- Below Black 88
- Above Black 88
- Saturation 100
- Operation 101
- Primary Alignment 105
- Polarizer 115
- L R 116
- 6. External Control 119
- External Control 120
- Table 6-1. Serial Commands 121
- DBO R/W Yes -100 100 No 123
- DGO R/W Yes -100 100 No 123
- DRO R/W Yes -100 100 No 123
- IBO R/W Yes -32 32 No 125
- IGO R/W Yes -32 32 No 126
- IRO R/W Yes -32 32 No 126
- NFO R/W Yes 0 10 No 129
- Using Discrete IR 134
- (Standard Mode) 135
- (Standard Mode) (continued) 136
- (Extended Mode) 138
- Controller 139
- (continued) 140
- 7. Specifications 141
- Dimension Digital 143
- Specifications 143
- D-73d Dimensions 145
- Supported Timings 146
- 020-1082-02 Rev. A 152
- March 2014 152
Related products and manuals for Data projectors Runco D-73d Ultra
Data projectors Runco CL-410 Specifications
(57 pages)
(57 pages)
Data projectors Runco VX-8d Specifications
(88 pages)
(88 pages)
Data projectors Runco VX-60d Specifications
(126 pages)
(126 pages)
Data projectors Runco DR-300c User Manual
(36 pages)
(36 pages)
Data projectors Runco CL-420 Specifications
(72 pages)
(72 pages)
Data projectors Runco VX-8d Specifications
(104 pages)
(104 pages)
© 2020, manymanuals.com. All rights reserved. | 1.697 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals