Runco VX-44D User Manual Page 57
- Page / 120
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Installation
Runco VX-44d/-55d Installation/Operation Manual 41
PRE
L
IMINAR
Y
3.9
Primary Lens
Adjustments
To access the motorized primary lens controls:
1. Press MENU on the remote control or DHD Controller front panel.
2. Select Service from the Main Menu and enter the Service Menu passcode.
3. Select Display Device from the Service Menu.
4. Select Configure from the Display Device menu, then select Lens.
The Lens menu gives you a great deal of control over the picture size, position and focus.
For best results, use the internal 13-point test pattern
on the VX-44d/-55d when making these adjustments.
(You cannot access this test pattern from the DHD
Controller.) This pattern provides nine screen “zones”
with 13 targets.
To access this test pattern:
1. On the VX-44d/-55d built-in keypad (see Figure
2-3), press MENU.
2. Press or to highlight Installation, then press ENTER.
3. Press or to highlight Calibration and Test Patterns, then press ENTER.
4. Press or to highlight Test Pattern, then press ENTER.
5. Select the 13 Point test pattern from the pull-down list, then press ENTER.
Focus and ZoomTo focus the projected image, use the cursor buttons to highlight “In” or “Out.” Then,
press and hold the ENTER button.
To make the picture smaller (zoom out), use the cursor buttons to highlight the minus sign
(-). Then, press and hold the ENTER button.
To enlarge the picture (zoom in), use the cursor buttons to highlight the plus sign (+).
Then, press and hold the ENTER button.
Vertical and Horizontal
Lens Shift
To change the lens position, use the cursor buttons to highlight “Left,” “Right,” “Up” or
“Down” in the Lens menu. Then, press and hold the ENTER button to shift the lens in that
direction.
When finished adjusting the lens, press EXIT repeatedly on the VX-44d/-55d built-in
keypad to exit test pattern mode.
3.10
Adjusting the Picture
Orientation
By default, the VX-44d/-55d is configured for a “floor/front” installation, in which the
projector is installed upright and in front of the screen. If it is installed behind the screen
and/or mounted on a ceiling, you must change the picture orientation. To do this:
1. Press MENU on the remote control or DHD Controller front panel.
2. Select Service from the Main Menu and enter the Service Menu passcode.
3. Select Display Device from the Service Menu.
4. Select Configure from the Display Device menu, then select Installation.
5. Select Orientation.
6. Choose Floor/Rear, Ceiling/Front or Ceiling/Rear, to match the installation method.
- NSTALLATION/OPERATION MANUAL 1
- Warranty 3
- Important Safety Instructions 7
- Compliance Information 8
- Table of Contents 11
- List of Figures 15
- 1. Introduction 17
- Using This Manual 18
- Description, Features 19
- Introduction 20
- 2. Controls and Functions 21
- 1 7 863 5 92 4 22
- Controls and Functions 23
- VX-44d/-55d Built-In 24
- DHD Controller Front 26
- DHD Controller Rear 28
- (not available on 30
- (“CUST 2” on 30
- 3. Installation 33
- Quick Setup 34
- Installation 35
- Considerations 35
- Estimating Throw Distance 36
- Screen width (w) 36
- Ceiling Installation 37
- Floor Installation 37
- Installing the 41
- Projection Lens 41
- Installing the Optional 42
- CineWide Lens Mount 42
- AutoScope stand used 43
- Mounting the 44
- Connections to the 45
- VX-44d/-55d and DHD 45
- Controller 45
- DTV-Set-Top Box 48
- (DTV-STB) 48
- RGB Camcorder 49
- Figure 3-13 50
- Gaming Console 51
- Camcorder 51
- Control System 52
- AutoScope Lens Motor 53
- IR Sensor 54
- IR Repeater 54
- Remote Control 54
- Aspect Ratio 56
- Input Resolution/Frame Rate 56
- Installing and 58
- Adjusting the 58
- CineWide Anamorphic 58
- Too Far Right 59
- Too Far Left 59
- Correct position 59
- Too High 60
- Correct Lens Angle 60
- Incorrect Lens Angle 60
- Anamorphic Lens (Top View) 61
- Optimizing Lamp and 62
- Lens Performance 62
- Working With the 65
- RVR 7 67
- 4. Operation 69
- 4:3 Image on 72
- 16:9 Display 72
- (Letterbox aspect ratio) 72
- 1080i HDTV Image 73
- 720p HDTV Image 73
- Below Black 74
- Operation 75
- No Overscan Crop Zoom 79
- Advanced Color Temp 84
- Input Names 87
- Vertical Keystone Correction 88
- Lamp cover - 2 screws 93
- Front Filter Access Cover 95
- Side Filter Access Cover 95
- Troubleshooting Tips 97
- 6. External Control 103
- Table 6-1. Serial Commands 104
- Using Discrete IR 108
- Start Bits Toggle Bit 109
- Address Bits Command Bits 109
- 11010001000001 109
- 7. Specifications 111
- DHD Controller 113
- Specifications 113
- VX-44d/-55d 114
- Dimensions 114
- Supported Timings 115
- 020-0826-02 Rev. B 120
- April 2009 120
Related products and manuals for Projectors Runco VX-44D
Projectors Runco VX-6c User Manual
(110 pages)
(110 pages)
Projectors Runco VX-5C User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 0.533 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals