Runco VX-44D User Manual Page 65
- Page / 120
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Installation
Runco VX-44d/-55d Installation/Operation Manual 49
PRE
L
IMINAR
Y
3.13
Working With the
Lamp
Access the Lamp Adjust menu to:
• Choose a lamp mode for regulating power and light output.
• Change the optical aperture size.
• View information pertaining to past and present lamps.
To access the Lamp Adjust menu, press MENU on the VX-44d/-55d built-in keypad
(
Figure 2-3). Then, Select Lamp Adjust from the Main Menu.
Lamp Hours (read-only): Lamp Hours shows the number of hours logged on the
current lamp. Whenever you record a new lamp serial number, the VX-44d/-55d
automatically resets this value to zero and begins to log time for the new lamp.
Lamp S/N (read-only): Lamp S/N is the serial number recorded for the current lamp.
When you install a new lamp and enter its serial number, the number appears here.
Lamp Message: Enter a check mark for Lamp Message to enable a warning message
that appears upon power-up when the lamp has reached the specified lamp limit and
should be replaced. Delete the check mark to prevent display of this message – instead,
when your lamp expires, only the status display messages on the back of the projector will
provide a visual warning to replace the lamp.
Lamp Limit: Set Lamp Limit to the number of hours you expect to log on the current
lamp before replacing it. This will trigger a lamp message on-screen (if enabled).
Lamp Hours 147
Lamp S/N 123456789
1. Lamp Message
2. Lamp Limit 1000
3. Lamp Mode Power
4. Power 500
5. Intensity 0
6. RVR 3
7. Lamp History
8. Change Lamp
Lamp Adjust
You can also perform this task through the DHD Controller. For
more information, refer to
Lamp on page 66.
You can also perform this task through the DHD Controller. For
more information, refer to
RVR on page 68.
You can also obtain this information through the DHD Controller.
For more information, refer to
Lamp Info on page 72.
For detailed lamp replacement instructions, refer to Lamp and
Filter Replacement on page 77.
1. It is recommended that the Lamp Message check box remain
enabled.
2. When a lamp warning message appears, press EXIT to
temporarily dismiss the warning. The message will continue to
appear upon power-up until you install a new lamp.
Note
Note
Note
Note
Note
- NSTALLATION/OPERATION MANUAL 1
- Warranty 3
- Important Safety Instructions 7
- Compliance Information 8
- Table of Contents 11
- List of Figures 15
- 1. Introduction 17
- Using This Manual 18
- Description, Features 19
- Introduction 20
- 2. Controls and Functions 21
- 1 7 863 5 92 4 22
- Controls and Functions 23
- VX-44d/-55d Built-In 24
- DHD Controller Front 26
- DHD Controller Rear 28
- (not available on 30
- (“CUST 2” on 30
- 3. Installation 33
- Quick Setup 34
- Installation 35
- Considerations 35
- Estimating Throw Distance 36
- Screen width (w) 36
- Ceiling Installation 37
- Floor Installation 37
- Installing the 41
- Projection Lens 41
- Installing the Optional 42
- CineWide Lens Mount 42
- AutoScope stand used 43
- Mounting the 44
- Connections to the 45
- VX-44d/-55d and DHD 45
- Controller 45
- DTV-Set-Top Box 48
- (DTV-STB) 48
- RGB Camcorder 49
- Figure 3-13 50
- Gaming Console 51
- Camcorder 51
- Control System 52
- AutoScope Lens Motor 53
- IR Sensor 54
- IR Repeater 54
- Remote Control 54
- Aspect Ratio 56
- Input Resolution/Frame Rate 56
- Installing and 58
- Adjusting the 58
- CineWide Anamorphic 58
- Too Far Right 59
- Too Far Left 59
- Correct position 59
- Too High 60
- Correct Lens Angle 60
- Incorrect Lens Angle 60
- Anamorphic Lens (Top View) 61
- Optimizing Lamp and 62
- Lens Performance 62
- Working With the 65
- RVR 7 67
- 4. Operation 69
- 4:3 Image on 72
- 16:9 Display 72
- (Letterbox aspect ratio) 72
- 1080i HDTV Image 73
- 720p HDTV Image 73
- Below Black 74
- Operation 75
- No Overscan Crop Zoom 79
- Advanced Color Temp 84
- Input Names 87
- Vertical Keystone Correction 88
- Lamp cover - 2 screws 93
- Front Filter Access Cover 95
- Side Filter Access Cover 95
- Troubleshooting Tips 97
- 6. External Control 103
- Table 6-1. Serial Commands 104
- Using Discrete IR 108
- Start Bits Toggle Bit 109
- Address Bits Command Bits 109
- 11010001000001 109
- 7. Specifications 111
- DHD Controller 113
- Specifications 113
- VX-44d/-55d 114
- Dimensions 114
- Supported Timings 115
- 020-0826-02 Rev. B 120
- April 2009 120
Related products and manuals for Projectors Runco VX-44D
Projectors Runco VX-6c User Manual
(110 pages)
(110 pages)
Projectors Runco VX-5C User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 0.877 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals