Runco VX-1000d Specifications Page 76
- Page / 90
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Maintenance and Troubleshooting
64 Runco VX-2000d Owner’s Operating Manual
PRE
L
IMINAR
Y
5.2
Troubleshooting Tips
Table 5-1 provides some general guidelines for troubleshooting problems you may
encounter with the VX-2000d.
If you encounter an issue not described here or in Section 3 (refer to Installation
Considerations on page 20), or if the suggested solutions fail to resolve the problem,
please contact your Runco dealer or Runco Technical Support.
Table 5-1. Troubleshooting Chart
Symptom Possible Cause(s) Solution
The projector does not turn
on after initial installation. The
power LED on the front of the
DHD Controller lights red after
you press the power button.
• The VX-2000d is not
plugged in or the AC outlet
is not active.
• The serial connection from
the DHD Controller to the
VX-2000d is incorrect.
•The remote control
batteries have run out.
• Ensure that the VX-2000d
is plugged in and that the
AC outlet is active.
• Ensure that the RS-232
output from the DHD
Controller is properly
connected to the RS-232C
port on the VX-2000d (see
Figure 3-6).
• Replace the batteries.
The projector and DHD
Controller are both on, but
there is no picture and
on-screen menus do not
appear.
• Faulty or incorrect video
connection between the
DHD Controller and the
VX-2000d.
• Ensure that the HDMI
output from the DHD
Controller is properly
connected to the HDMI
input on the VX-2000d
(see
Figure 3-6).
The projector and
DHD
Controller are both on
and menus appear
on-screen, but there is no
picture.
• Incorrect source selection.
• Source component is not
turned on.
• Source component is
connected incorrectly or
not at all.
• Select the correct source.
• Turn on the source.
• Check video connections
to source component.
A projected image from a
DVD is split or otherwise
scrambled.
• DVD player is connected
to the Component input
and set to progressive
scan mode.
• Turn off progressive scan
on the DVD player. Or,
connect the DVD player to
the HD1 or HD2 input.
Image is too bright and/or
lacks definition in the bright
areas of the image.
• Contrast is set too high. • Lower the contrast setting.
Image appears “washed out”
and/or dark areas appear too
bright.
• Brightness is set too high. • Lower the brightness
setting.
Colors in the image are
swapped (for example, reds
appear blue or vice versa) on
one or more sources.
• The Red/Pr, Green/Y or
Blue/Pb outputs from the
source are connected to
the wrong inputs on the
DHD Controller.
• Ensure that the source
outputs are connected to
the correct DHD Controller
input.
- VX-2000d 1
- TWO YEAR LIMITED WARRANTY 3
- Safety Precautions 6
- Table of Contents 10
- List of Figures 11
- 1. Introduction 13
- Using This Manual 14
- Description, Features 15
- Introduction 16
- 2. Controls and Functions 17
- Controls and Functions 18
- VX-2000d Rear Panel 19
- DHD Controller Front 20
- DHD Controller Rear 22
- VX-2000d Remote 24
- Control Unit 24
- VX-2000d Built-In 27
- 7m/23ft 29
- Installation 30
- Quick Setup 31
- Considerations 32
- Estimating Throw Distance 33
- Screen width (w) 33
- Floor Installation 34
- Mounting the 36
- Connections to the 37
- VX-2000d and DHD 37
- Controller 37
- HDMI Source 38
- (HD-DVD/BD/DVD Player or 38
- HD Tuner with 38
- HDMI or DVI out) 38
- Personal Computer 40
- Red Green Blue Horiz Vert 40
- DVD Player, VCR 41
- Satellite Receiver 41
- Laser Disc etc 41
- Control System 42
- IR Receiver 43
- Current Source Format 44
- Resolution 44
- Aspect Ratio 44
- Primary Lens 45
- Adjustments 45
- Installing and 46
- Adjusting the 46
- CineWide Anamorphic 46
- Too High 47
- Correct position 47
- 4. Operation 49
- Chroma Delay 50
- 4:3 Image, stretched to fill 52
- 16:9 Screen (Display) 52
- 16:9 Image on 52
- 2.35:1 Image on 53
- 16:9 Screen 53
- Below Black 54
- Operation 55
- the White Balance sub-menu 59
- On-Screen Menus for 65
- 1080i (Digital) or 65
- 1080p Signals 65
- Sources (continued) 68
- THESE SCREWS 75
- Troubleshooting Tips 76
- Table 6-1. Serial Commands 79
- 7. Specifications 85
- DHD Controller 87
- Specifications 87
- VX-2000d Dimensions 88
- SERIAL NUMBER 90
Related products and manuals for Data projectors Runco VX-1000d
Data projectors Runco VX-8d Specifications
(88 pages)
(88 pages)
Data projectors Runco VX-60d Specifications
(126 pages)
(126 pages)
Data projectors Runco DR-300c User Manual
(36 pages)
(36 pages)
Data projectors Runco CL-420 Specifications
(72 pages)
(72 pages)
Data projectors Runco VX-8d Specifications
(104 pages)
(104 pages)
Data projectors Runco VX-2c Setup Guide
(36 pages)
(36 pages)
Data projectors Runco CL-500 User Manual
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 0.293 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals