Runco VX-44D User Manual Page 66
- Page / 120
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Installation
50 Runco VX-44d/-55d Installation/Operation Manual
PRE
L
IMINAR
Y
Lamp Mode: Select the Lamp Mode you want to use in order to control the light output.
You can choose to run the lamp as bright as possible, you can power the lamp with a
specific wattage appropriate for the installed lamp or you can set a specific intensity
(brightness) to maintain. Keep in mind that higher lamp power settings can shorten lamp
life.
Use the lamp mode that best suits your brightness needs:
• Max Brightness: The lamp will always burn as brightly as possible, driven by 100% of
the power level rating for the installed lamp (1,000 watts for the VX-44d or 1,200 watts
for the VX-55d). Keep in mind that the “maximum brightness” for any lamp gradually
diminishes over time.
•Intensity: Brightness will remain close to a specified level for as long as possible. If you
select this option, enter a number representing the intensity level (brightness) you want
to maintain – the VX-44d/-55d automatically adjusts power as needed to maintain this
intensity as closely as possible.
This value and slidebar represents the current brightness of your lamp, decreasing over
time when you are operating in Max Brightness mode or at a specific Power level.
When you operate in Intensity mode, this value remains at the chosen Intensity setting
and cannot be adjusted.
To use “Intensity” mode, judge by eye (or use a meter) and set the level as desired for
your application. Over time, the projector will automatically increase the power supplied
to the lamp as needed to maintain the chosen intensity as closely as possible.
•Power: The power supplied to the lamp will remain at your specified wattage level.
Once you select this option, enter the number of watts representing the power level you
wish to maintain.
This slidebar and number indicates how many watts are applied to the lamp. You can
apply anywhere from approximately 60% to 65% of the maximum power intended for
the installed lamp up to 100% of the lamp rating. Set for the number of watts as
desired, keeping in mind that lower power levels produce dimmer images. When in
either Power or Max Brightness modes, the power level remains constant. Specifying a
maximum power level here is the same as operating in Max Brightness mode.
1. If you change modes over the life of a lamp, the lamp limit you
originally expected may no longer be possible.
2. Turning the lamp on and off reduces lamp life significantly, as do
other factors.
3. It is recommended that Lamp Limit not exceed the expected
lamp life, otherwise a lamp could become dangerously fragile
with overuse.
Note
The Intensity value is not the actual lumen output, but rather a
correlated value only – 1246 may represent 3500 lumens, for
example.
Note
- NSTALLATION/OPERATION MANUAL 1
- Warranty 3
- Important Safety Instructions 7
- Compliance Information 8
- Table of Contents 11
- List of Figures 15
- 1. Introduction 17
- Using This Manual 18
- Description, Features 19
- Introduction 20
- 2. Controls and Functions 21
- 1 7 863 5 92 4 22
- Controls and Functions 23
- VX-44d/-55d Built-In 24
- DHD Controller Front 26
- DHD Controller Rear 28
- (not available on 30
- (“CUST 2” on 30
- 3. Installation 33
- Quick Setup 34
- Installation 35
- Considerations 35
- Estimating Throw Distance 36
- Screen width (w) 36
- Ceiling Installation 37
- Floor Installation 37
- Installing the 41
- Projection Lens 41
- Installing the Optional 42
- CineWide Lens Mount 42
- AutoScope stand used 43
- Mounting the 44
- Connections to the 45
- VX-44d/-55d and DHD 45
- Controller 45
- DTV-Set-Top Box 48
- (DTV-STB) 48
- RGB Camcorder 49
- Figure 3-13 50
- Gaming Console 51
- Camcorder 51
- Control System 52
- AutoScope Lens Motor 53
- IR Sensor 54
- IR Repeater 54
- Remote Control 54
- Aspect Ratio 56
- Input Resolution/Frame Rate 56
- Installing and 58
- Adjusting the 58
- CineWide Anamorphic 58
- Too Far Right 59
- Too Far Left 59
- Correct position 59
- Too High 60
- Correct Lens Angle 60
- Incorrect Lens Angle 60
- Anamorphic Lens (Top View) 61
- Optimizing Lamp and 62
- Lens Performance 62
- Working With the 65
- RVR 7 67
- 4. Operation 69
- 4:3 Image on 72
- 16:9 Display 72
- (Letterbox aspect ratio) 72
- 1080i HDTV Image 73
- 720p HDTV Image 73
- Below Black 74
- Operation 75
- No Overscan Crop Zoom 79
- Advanced Color Temp 84
- Input Names 87
- Vertical Keystone Correction 88
- Lamp cover - 2 screws 93
- Front Filter Access Cover 95
- Side Filter Access Cover 95
- Troubleshooting Tips 97
- 6. External Control 103
- Table 6-1. Serial Commands 104
- Using Discrete IR 108
- Start Bits Toggle Bit 109
- Address Bits Command Bits 109
- 11010001000001 109
- 7. Specifications 111
- DHD Controller 113
- Specifications 113
- VX-44d/-55d 114
- Dimensions 114
- Supported Timings 115
- 020-0826-02 Rev. B 120
- April 2009 120
Related products and manuals for Projectors Runco VX-44D
Projectors Runco VX-6c User Manual
(110 pages)
(110 pages)
Projectors Runco VX-5C User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 0.125 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals