Runco Q-750d Ultra Series Specifications Page 60
- Page / 134
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Installation
44 Q-750d Ultra Series Installation/Operation Manual
PRE
L
IMINAR
Y
3.9
Primary Lens
Adjustments
The Q-750d Ultra gives you a great deal of control over the picture size, position and
focus.
Focus and Zoom To focus the projected image, grasp the lens by
the outer ring and rotate it.
To make the picture smaller (zoom out) or larger
(zoom in), move the zoom tab in the appropriate
direction.
Lens Shift To access the lens shift controls, loosen the Phillips screw at the bottom of the decorative
bezel on the front of the projector (see below). Then, remove the bezel.
Vertical Lens Shift: To shift the
projected image vertically, insert the
provided hex wrench into the vertical lens
shift adjuster at the top of the projector
(directly above the lens). Then, turn the
wrench as shown to shift the lens in the
desired direction.
Horizontal Lens Shift: To shift the
projected image horizontally, insert the
provided hex wrench into the horizontal
lens shift adjuster at the top of the
projector. Then, turn the wrench as shown
to shift the lens in the desired direction.
When you have finished adjusting the lens position, re-install the front bezel.
3.10
Adjusting the Picture
Orientation
By default, the Q-750d Ultra is configured for a “floor/front” installation, in which the
projector is installed upright and in front of the screen. If it is installed behind the screen
and/or mounted on a ceiling, you must change the picture orientation. To do this:
1. On the DHD Controller remote control or front panel, press MENU.
2. Select Service from the Main Menu and enter the Service Menu passcode.
3. Select Display Device from the Service Menu.
4. Select Configure from the Display Device menu, then select Installation.
5. Select Orientation, then choose Floor/Rear, Ceiling/Front or Ceiling/Rear, to match
the installation method. Or, for front-projection installations, use the Auto setting to
have the projector automatically determine the orientation (floor or ceiling) using an
internal sensor.
➤
Zoom
in
Focus
Zoom out
➤
Vertical
Lens Shift
Lens
Horizontal
Lens Shift
You must enter a passcode to access the Service menu.
Note
- Q-750d Ultra Series 1
- Warranty 3
- Important Safety Instructions 7
- Compliance Information 8
- Table of Contents 11
- List of Figures 15
- 1. Introduction 17
- Using This Manual 18
- Description, Features 19
- Introduction 20
- 2. Controls and Functions 21
- Q-750d Ultra Rear 22
- DHD Controller Front 23
- DHD Controller Rear 24
- Controls and Functions 25
- Q-750d Ultra Remote 26
- Control Unit 26
- 3. Installation 29
- Quick Setup 30
- Installation 31
- Considerations 31
- Estimating Throw Distance 32
- Screen width (w) 32
- Ceiling Installation 34
- Floor Installation 34
- Installing the Primary 37
- Projection Lens 37
- Installing the Optional 40
- CineWide/AutoScope 40
- Lens Mount 40
- Mounting the Q-750d 46
- HDMI Out 47
- To Display 47
- DTV-Set-Top Box 50
- (DTV-STB) 50
- RGB Camcorder 51
- Figure 3-15 52
- Gaming Console 53
- Camcorder 53
- Audio Processor/ 54
- Switcher 54
- Secondary Display 54
- Control System 55
- AutoScope Lens Motor 56
- Turning on the Power 59
- Vertical 60
- Lens Shift 60
- Horizontal 60
- Adjusting the Image 61
- Geometry 61
- Installing and 63
- Adjusting the 63
- CineWide Anamorphic 63
- Too Far Right 65
- Too Far Left 65
- Correct position 65
- Too High 66
- Correct Lens Angle 66
- Incorrect Lens Angle 66
- Anamorphic Lens (Top View) 67
- 4. Operation 69
- 4:3 Image on 72
- 16:9 Display 72
- (Letterbox aspect ratio) 72
- 1080i HDTV Image 73
- 720p HDTV Image 73
- Below Black 75
- Off Crop Zoom 79
- Saturation 86
- Input Names 91
- Operation 100
- 6. External Control 103
- External Control 104
- Table 6-1. Serial Commands 105
- DBO R/W Yes -100 100 No 107
- DGO R/W Yes -100 100 No 107
- DRO R/W Yes -100 100 No 107
- IGO R/W Yes -32 32 No 109
- IBO R/W Yes -32 32 No 109
- IRO R/W Yes -32 32 No 110
- Using Discrete IR 118
- Using HDMI CEC 122
- Messages 122
- 7. Specifications 125
- DHD Controller 127
- Specifications 127
- Overall Dimensions – 129
- Q-750d Ultra 129
- Ultra/CineWide with 130
- AutoScope 130
- Supported Timings 131
- 020-1159-00 Rev. B 134
- November 2011 134
Related products and manuals for Data projectors Runco Q-750d Ultra Series
Data projectors Runco VX-8d Specifications
(104 pages)
(104 pages)
Data projectors Runco VX-2c Setup Guide
(36 pages)
(36 pages)
Data projectors Runco CL-500 User Manual
(32 pages)
(32 pages)
Data projectors Runco XP-103DHD Specifications
(126 pages)
(126 pages)
Data projectors Runco VX-4000d Specifications
(108 pages)
(108 pages)
Data projectors Runco VX-2i Specifications
(112 pages)
(112 pages)
© 2020, manymanuals.com. All rights reserved. | 1.298 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals