Runco Q-750d Ultra Series Specifications Page 87
- Page / 134
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Operation
Q-750d Ultra Series Installation/Operation Manual 71
PRE
L
IMINAR
Y
• White Balance: To precisely adjust the white point associated with the custom
color gamut, choose White Balance from the PCE sub-menu. These controls
operate identically to the Gain controls in the Display Color - Common Settings
menu (described on page 67).
Display Color - Projector Settings: These settings are also saved independently for
each input and display mode.
• SatCo (BrilliantColor™): Select SatCo (BrilliantColor™) from the Display Color -
Projector Settings menu to enable (On) or disable (Off) BrilliantColor processing, which
improves brightness in grays and secondary colors.
•ConstantContrast: Select ConstantContrast from the Display Color - Common
Settings menu to enable (Low/Medium/High) or disable (Off) ConstantContrast in the
optical engine. ConstantContrast uses a dynamic LED driver that modulates light to the
DMD based on the actual content of the video material. Runco recommends that you
disable ConstantContrast before adjusting Brightness, Contrast or other image
settings.
Input Image: The Input Image controls are functionally similar to those in the Picture
menu (refer to page 58), but are accessible only by entering the Calibration menu
passcode.
Input Color: The Input Color controls are similar to those in the Display Color menu (see
above), but adjust the color balance of the incoming signal. These settings are also saved
independently for each input and display mode.
•Gain/Offset (HD1, HD2 and Component/SCART inputs only): These controls
operate similarly to those in the Display Color - Common Settings menu (described
on page 67), but affect the Y, Pb and Pr signal components rather than the red, green
and blue channels.
•Chroma Delay: use the Chroma Delay control to correct a mis-aligned image from a
composite video source. Chroma delay in an image causes color shifts to occur to the
left of the vertical edge transitions, producing artificial shadows or a “halo” effect. If
necessary, adjust this setting to eliminate them.
•Noise Filter: To apply noise filtering to the input signal, select Noise Filter from the
Input Color menu. The Noise Filter is useful for clearing up noisy images from 480i
video sources.
Use the left- or right-arrow buttons to select the desired amount of noise reduction,
keeping in mind that higher settings (which reduce high frequencies) may also “soften”
the image.
Save ISF Night/Save ISF Day: Whenever you make a change to the ISF settings, you
should always save it. Select Save ISF Night or Save ISF Day from the Calibration menu to
do this.
The Input Image settings establish the “zero point” for the Picture
menu settings, whose values represent offsets from the Input
Image settings. For example, if you set Brightness to 10 in this
menu, setting Brightness to 10 in the Picture menu results in an
actual setting value of 20 (10+10).
Note
- Q-750d Ultra Series 1
- Warranty 3
- Important Safety Instructions 7
- Compliance Information 8
- Table of Contents 11
- List of Figures 15
- 1. Introduction 17
- Using This Manual 18
- Description, Features 19
- Introduction 20
- 2. Controls and Functions 21
- Q-750d Ultra Rear 22
- DHD Controller Front 23
- DHD Controller Rear 24
- Controls and Functions 25
- Q-750d Ultra Remote 26
- Control Unit 26
- 3. Installation 29
- Quick Setup 30
- Installation 31
- Considerations 31
- Estimating Throw Distance 32
- Screen width (w) 32
- Ceiling Installation 34
- Floor Installation 34
- Installing the Primary 37
- Projection Lens 37
- Installing the Optional 40
- CineWide/AutoScope 40
- Lens Mount 40
- Mounting the Q-750d 46
- HDMI Out 47
- To Display 47
- DTV-Set-Top Box 50
- (DTV-STB) 50
- RGB Camcorder 51
- Figure 3-15 52
- Gaming Console 53
- Camcorder 53
- Audio Processor/ 54
- Switcher 54
- Secondary Display 54
- Control System 55
- AutoScope Lens Motor 56
- Turning on the Power 59
- Vertical 60
- Lens Shift 60
- Horizontal 60
- Adjusting the Image 61
- Geometry 61
- Installing and 63
- Adjusting the 63
- CineWide Anamorphic 63
- Too Far Right 65
- Too Far Left 65
- Correct position 65
- Too High 66
- Correct Lens Angle 66
- Incorrect Lens Angle 66
- Anamorphic Lens (Top View) 67
- 4. Operation 69
- 4:3 Image on 72
- 16:9 Display 72
- (Letterbox aspect ratio) 72
- 1080i HDTV Image 73
- 720p HDTV Image 73
- Below Black 75
- Off Crop Zoom 79
- Saturation 86
- Input Names 91
- Operation 100
- 6. External Control 103
- External Control 104
- Table 6-1. Serial Commands 105
- DBO R/W Yes -100 100 No 107
- DGO R/W Yes -100 100 No 107
- DRO R/W Yes -100 100 No 107
- IGO R/W Yes -32 32 No 109
- IBO R/W Yes -32 32 No 109
- IRO R/W Yes -32 32 No 110
- Using Discrete IR 118
- Using HDMI CEC 122
- Messages 122
- 7. Specifications 125
- DHD Controller 127
- Specifications 127
- Overall Dimensions – 129
- Q-750d Ultra 129
- Ultra/CineWide with 130
- AutoScope 130
- Supported Timings 131
- 020-1159-00 Rev. B 134
- November 2011 134
Related products and manuals for Data projectors Runco Q-750d Ultra Series
Data projectors Runco VX-8d Specifications
(104 pages)
(104 pages)
Data projectors Runco VX-2c Setup Guide
(36 pages)
(36 pages)
Data projectors Runco CL-500 User Manual
(32 pages)
(32 pages)
Data projectors Runco XP-103DHD Specifications
(126 pages)
(126 pages)
Data projectors Runco VX-4000d Specifications
(108 pages)
(108 pages)
Data projectors Runco VX-2i Specifications
(112 pages)
(112 pages)
© 2020, manymanuals.com. All rights reserved. | 1.172 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals