Runco Q-750d Ultra Series Specifications Page 88
- Page / 134
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Operation
72 Q-750d Ultra Series Installation/Operation Manual
PRE
L
IMINAR
Y
Copy/Paste - Memory Preset: You can copy and paste settings from one memory
preset to another. This gives you a convenient starting point for creating a new preset
based on an existing one, to make the calibration process less time-consuming.
For example, you can use the Copy/Paste Memory Preset feature to:
• Apply settings from HDMI 1 to HDMI 2, or from HD1 to HD2.
• Calibrate an input for 720p source signals, then use those settings for 1080i sources.
• Duplicate ISF Night settings for a given source and signal format and save them in the
Custom 1 memory preset.
To use this feature, select Copy/Paste from the Calibration menu, then select Memory
Preset.
•Memory Preset - Copy Settings: Select Copy Settings from the Copy/Paste
Memory Preset menu to place the settings for the current input source, signal format
(resolution and frame rate) and memory preset onto a “clipboard,” which is a temporary
memory location. When you do, the message “Settings Copied” briefly appears
on-screen. The Copy/Paste menu then re-appears, indicating the source of the copied
settings.
•Memory Preset - Paste Settings: To apply the settings on the clipboard to a
different input source, signal format and/or memory preset, do any or all of the
following:
• Switch to another input (for example, from HD1 to HD2).
• Change the output signal format at the source (for example, from 720p/60 to
1080i/60).
• Switch to another Memory Preset (for example, from ISF Night to Custom 1).
Then, select Paste Settings from the Copy/Paste Memory Preset menu. If you want
to keep these new settings, you must save them! (Refer to Save ISF Night/Save
ISF Day on page 71 or Memory Presets on page 64.)
Copy/Paste - Aspect Ratio: You can also copy and paste certain settings, such as
those for Output Shift and Image Alignment (refer to page 73) from one aspect ratio or
“screen” (refer to Screen on page 58) to another.
To do this, select Copy/Paste from the Calibration menu, then select Aspect Ratio.
•Aspect Ratio - Copy Settings: Select Copy Settings from the Copy/Paste Aspect
Ratio menu to place the Output Shift and Image Alignment settings for the current
aspect ratio onto a “clipboard,” which is a temporary memory location. When you do,
the message “Settings Copied” briefly appears on-screen. The Copy/Paste menu then
re-appears, indicating the source of the copied settings.
Copy/Paste
Memory Preset
Aspect Ratio
Memory Preset
Copy Settings
Paste Settings
Copied From:
Input Source HDMI 1
Signal Format 1080p/60
Memory Preset ISF Night
Copied settings are not retained after a power cycle.
Note
Copy/Paste
Memory Preset
Aspect Ratio
Aspect Ratio
Copy Settings
Paste Settings
Copied From:
Aspect Ratio 16:9
Screen Screen 1
Copied settings are not retained after a power cycle.
Note
- Q-750d Ultra Series 1
- Warranty 3
- Important Safety Instructions 7
- Compliance Information 8
- Table of Contents 11
- List of Figures 15
- 1. Introduction 17
- Using This Manual 18
- Description, Features 19
- Introduction 20
- 2. Controls and Functions 21
- Q-750d Ultra Rear 22
- DHD Controller Front 23
- DHD Controller Rear 24
- Controls and Functions 25
- Q-750d Ultra Remote 26
- Control Unit 26
- 3. Installation 29
- Quick Setup 30
- Installation 31
- Considerations 31
- Estimating Throw Distance 32
- Screen width (w) 32
- Ceiling Installation 34
- Floor Installation 34
- Installing the Primary 37
- Projection Lens 37
- Installing the Optional 40
- CineWide/AutoScope 40
- Lens Mount 40
- Mounting the Q-750d 46
- HDMI Out 47
- To Display 47
- DTV-Set-Top Box 50
- (DTV-STB) 50
- RGB Camcorder 51
- Figure 3-15 52
- Gaming Console 53
- Camcorder 53
- Audio Processor/ 54
- Switcher 54
- Secondary Display 54
- Control System 55
- AutoScope Lens Motor 56
- Turning on the Power 59
- Vertical 60
- Lens Shift 60
- Horizontal 60
- Adjusting the Image 61
- Geometry 61
- Installing and 63
- Adjusting the 63
- CineWide Anamorphic 63
- Too Far Right 65
- Too Far Left 65
- Correct position 65
- Too High 66
- Correct Lens Angle 66
- Incorrect Lens Angle 66
- Anamorphic Lens (Top View) 67
- 4. Operation 69
- 4:3 Image on 72
- 16:9 Display 72
- (Letterbox aspect ratio) 72
- 1080i HDTV Image 73
- 720p HDTV Image 73
- Below Black 75
- Off Crop Zoom 79
- Saturation 86
- Input Names 91
- Operation 100
- 6. External Control 103
- External Control 104
- Table 6-1. Serial Commands 105
- DBO R/W Yes -100 100 No 107
- DGO R/W Yes -100 100 No 107
- DRO R/W Yes -100 100 No 107
- IGO R/W Yes -32 32 No 109
- IBO R/W Yes -32 32 No 109
- IRO R/W Yes -32 32 No 110
- Using Discrete IR 118
- Using HDMI CEC 122
- Messages 122
- 7. Specifications 125
- DHD Controller 127
- Specifications 127
- Overall Dimensions – 129
- Q-750d Ultra 129
- Ultra/CineWide with 130
- AutoScope 130
- Supported Timings 131
- 020-1159-00 Rev. B 134
- November 2011 134
Related products and manuals for Data projectors Runco Q-750d Ultra Series
Data projectors Runco VX-8d Specifications
(104 pages)
(104 pages)
Data projectors Runco VX-2c Setup Guide
(36 pages)
(36 pages)
Data projectors Runco CL-500 User Manual
(32 pages)
(32 pages)
Data projectors Runco XP-103DHD Specifications
(126 pages)
(126 pages)
Data projectors Runco VX-4000d Specifications
(108 pages)
(108 pages)
Data projectors Runco VX-2i Specifications
(112 pages)
(112 pages)
© 2020, manymanuals.com. All rights reserved. | 3.656 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals