Runco Q-750d Ultra Series Specifications Page 89
- Page / 134
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Operation
Q-750d Ultra Series Installation/Operation Manual 73
PRE
L
IMINAR
Y
•Aspect Ratio - Paste Settings: To apply the Output Shift and Image Alignment
settings on the clipboard to a different aspect ratio and/or screen, do either of the
following:
• Switch to another aspect ratio (for example, from 16:9 to Cinema).
• Switch from Screen 1 to Screen 2 or vice versa.
Then, select Paste Settings from the Copy/Paste Aspect Ratio menu. The new settings
are saved automatically.
Output Shift: The Left/Right, Up/Down, Width and Height controls in the Output Shift
menu are similar to those in the Input Position menu, except that they change the
characteristics of the output signal. These settings are saved independently for each
aspect ratio and screen selection (refer to Screen on page 58).
• Screen Masking: .This control adjusts the amount of cropping on each edge of the
output image. This differs from the regular Overscan control in two ways:
• It allows separate adjustments on each edge; and
• It is saved per aspect ratio, per screen (as opposed to per connector, per mode).
This is useful for installations where the aspect ratio of the screen doesn’t exactly match
the aspect ratio of the display.
Image Alignment: Use the controls in the Image Alignment menu to ensure proper
image geometry; that is, a perfectly rectangular projected image with no keystoning or
pincushion. For detailed instructions, refer to Adjusting the Image Geometry on
page 45.
Splash Configure: Use the Splash Configure menu to control the appearance and
behavior of the “splash” screen that appears on the display upon power-up.
•Owner Name/ISF Calibrated/ISF Other: You can have the Q-750d Ultra display the
owner’s name, your name, the phrase “ISF Calibrated” and/or any other string, up to
30 characters in length.
Use the up or down cursor button to select a character. Use the right and left cursor
buttons to change the cursor position. Press MENU when you have finished entering
text.
• Splash Timer: When you turn on the Q-750d Ultra, it projects a welcome screen with
the Runco and ISF logos, along with the personalized information you enter as
described above. Select Splash Timer from the Splash Configure menu to set the
amount of time for which this screen appears. The range is from 5 to 60 seconds, in
one-second increments. Press or to set the timer, then press MENU.
• Splash Enable: When you have finished customizing the splash screen, select Splash
Enable from the Splash Configure menu. Then, select On and press ENTER.
OSD Position: To adjust the position of the OSD, select OSD Position from the
Calibration menu and press ENTER.
Press or to select “Hor.” or “Ver.” Then, press or to change the position.
- Q-750d Ultra Series 1
- Warranty 3
- Important Safety Instructions 7
- Compliance Information 8
- Table of Contents 11
- List of Figures 15
- 1. Introduction 17
- Using This Manual 18
- Description, Features 19
- Introduction 20
- 2. Controls and Functions 21
- Q-750d Ultra Rear 22
- DHD Controller Front 23
- DHD Controller Rear 24
- Controls and Functions 25
- Q-750d Ultra Remote 26
- Control Unit 26
- 3. Installation 29
- Quick Setup 30
- Installation 31
- Considerations 31
- Estimating Throw Distance 32
- Screen width (w) 32
- Ceiling Installation 34
- Floor Installation 34
- Installing the Primary 37
- Projection Lens 37
- Installing the Optional 40
- CineWide/AutoScope 40
- Lens Mount 40
- Mounting the Q-750d 46
- HDMI Out 47
- To Display 47
- DTV-Set-Top Box 50
- (DTV-STB) 50
- RGB Camcorder 51
- Figure 3-15 52
- Gaming Console 53
- Camcorder 53
- Audio Processor/ 54
- Switcher 54
- Secondary Display 54
- Control System 55
- AutoScope Lens Motor 56
- Turning on the Power 59
- Vertical 60
- Lens Shift 60
- Horizontal 60
- Adjusting the Image 61
- Geometry 61
- Installing and 63
- Adjusting the 63
- CineWide Anamorphic 63
- Too Far Right 65
- Too Far Left 65
- Correct position 65
- Too High 66
- Correct Lens Angle 66
- Incorrect Lens Angle 66
- Anamorphic Lens (Top View) 67
- 4. Operation 69
- 4:3 Image on 72
- 16:9 Display 72
- (Letterbox aspect ratio) 72
- 1080i HDTV Image 73
- 720p HDTV Image 73
- Below Black 75
- Off Crop Zoom 79
- Saturation 86
- Input Names 91
- Operation 100
- 6. External Control 103
- External Control 104
- Table 6-1. Serial Commands 105
- DBO R/W Yes -100 100 No 107
- DGO R/W Yes -100 100 No 107
- DRO R/W Yes -100 100 No 107
- IGO R/W Yes -32 32 No 109
- IBO R/W Yes -32 32 No 109
- IRO R/W Yes -32 32 No 110
- Using Discrete IR 118
- Using HDMI CEC 122
- Messages 122
- 7. Specifications 125
- DHD Controller 127
- Specifications 127
- Overall Dimensions – 129
- Q-750d Ultra 129
- Ultra/CineWide with 130
- AutoScope 130
- Supported Timings 131
- 020-1159-00 Rev. B 134
- November 2011 134
Related products and manuals for Data projectors Runco Q-750d Ultra Series
Data projectors Runco VX-8d Specifications
(104 pages)
(104 pages)
Data projectors Runco VX-2c Setup Guide
(36 pages)
(36 pages)
Data projectors Runco CL-500 User Manual
(32 pages)
(32 pages)
Data projectors Runco XP-103DHD Specifications
(126 pages)
(126 pages)
Data projectors Runco VX-4000d Specifications
(108 pages)
(108 pages)
Data projectors Runco VX-2i Specifications
(112 pages)
(112 pages)
© 2020, manymanuals.com. All rights reserved. | 0.333 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals