Runco Q-750d Ultra Series Specifications Page 93
- Page / 134
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Operation
Q-750d Ultra Series Installation/Operation Manual 77
PRE
L
IMINAR
Y
If you prefer to do this manually, set it to Off. The DHD Controller will ask if you want
to perform the upgrade the next time it is power-cycled.
• Check For New Firmware: To have the DHD Controller check for new firmware on
demand (and perform an upgrade if it finds a new version), select Check For New
Firmware from the Auto Firmware Upgrade menu. If the DHD Controller finds a new
firmware version, select Yes to perform the upgrade or No to return to the previous
menu.
• E-Mail Notification: Select E-Mail Notification from the Network menu to specify
when and to whom the DHD Controller sends error and service notification messages
via e-mail.
The notification messages are in the following format:
To: [E-Mail Address; see below]
From: [email protected]
Subject: [Type of notification] from Runco DHD4
Body:
This is an automated message sent from the Runco DHD4:
Notification: [One of the following:
“DHD Error” / “Display Error”
“Periodic Service Notification”
“Lamp Life Notification” / “Calibration Data”]
Detailed Description: [ If a DHD Error, one of the following:
“Fan Failure 1” / “Fan Failure 2”
“Overtemp 1” / “Overtemp 2”
“Initialization Failure”
If a Display Error, a device-specific
error message such as “Lamp Door Open”
If a Periodic Service Notification, the elapsed
time since the last notification
If a Lamp Life Notification, the number of hours
the lamp has been in service
If a Calibration Data message,
“See Attached File” ]
Serial Number: [DHD Controller serial number]
Customer Information: [From “Customer Information“ sub-menu;
see below]
Best Regards,
Runco International, LLC
1195 NW Compton Drive
Beaverton, OR 97006
1-800-237-8262
• E-Mail Address: To specify the destination e-mail address for error and service
notifications, select E-Mail Address from the E-Mail Notification menu. The
procedure is similar to that for setting the IP address (refer to IP Configuration on
page 76). Enter up to 45 alphnumeric characters.
- Q-750d Ultra Series 1
- Warranty 3
- Important Safety Instructions 7
- Compliance Information 8
- Table of Contents 11
- List of Figures 15
- 1. Introduction 17
- Using This Manual 18
- Description, Features 19
- Introduction 20
- 2. Controls and Functions 21
- Q-750d Ultra Rear 22
- DHD Controller Front 23
- DHD Controller Rear 24
- Controls and Functions 25
- Q-750d Ultra Remote 26
- Control Unit 26
- 3. Installation 29
- Quick Setup 30
- Installation 31
- Considerations 31
- Estimating Throw Distance 32
- Screen width (w) 32
- Ceiling Installation 34
- Floor Installation 34
- Installing the Primary 37
- Projection Lens 37
- Installing the Optional 40
- CineWide/AutoScope 40
- Lens Mount 40
- Mounting the Q-750d 46
- HDMI Out 47
- To Display 47
- DTV-Set-Top Box 50
- (DTV-STB) 50
- RGB Camcorder 51
- Figure 3-15 52
- Gaming Console 53
- Camcorder 53
- Audio Processor/ 54
- Switcher 54
- Secondary Display 54
- Control System 55
- AutoScope Lens Motor 56
- Turning on the Power 59
- Vertical 60
- Lens Shift 60
- Horizontal 60
- Adjusting the Image 61
- Geometry 61
- Installing and 63
- Adjusting the 63
- CineWide Anamorphic 63
- Too Far Right 65
- Too Far Left 65
- Correct position 65
- Too High 66
- Correct Lens Angle 66
- Incorrect Lens Angle 66
- Anamorphic Lens (Top View) 67
- 4. Operation 69
- 4:3 Image on 72
- 16:9 Display 72
- (Letterbox aspect ratio) 72
- 1080i HDTV Image 73
- 720p HDTV Image 73
- Below Black 75
- Off Crop Zoom 79
- Saturation 86
- Input Names 91
- Operation 100
- 6. External Control 103
- External Control 104
- Table 6-1. Serial Commands 105
- DBO R/W Yes -100 100 No 107
- DGO R/W Yes -100 100 No 107
- DRO R/W Yes -100 100 No 107
- IGO R/W Yes -32 32 No 109
- IBO R/W Yes -32 32 No 109
- IRO R/W Yes -32 32 No 110
- Using Discrete IR 118
- Using HDMI CEC 122
- Messages 122
- 7. Specifications 125
- DHD Controller 127
- Specifications 127
- Overall Dimensions – 129
- Q-750d Ultra 129
- Ultra/CineWide with 130
- AutoScope 130
- Supported Timings 131
- 020-1159-00 Rev. B 134
- November 2011 134
Related products and manuals for Data projectors Runco Q-750d Ultra Series
Data projectors Runco VX-8d Specifications
(104 pages)
(104 pages)
Data projectors Runco VX-2c Setup Guide
(36 pages)
(36 pages)
Data projectors Runco CL-500 User Manual
(32 pages)
(32 pages)
Data projectors Runco XP-103DHD Specifications
(126 pages)
(126 pages)
Data projectors Runco VX-4000d Specifications
(108 pages)
(108 pages)
Data projectors Runco VX-2i Specifications
(112 pages)
(112 pages)
© 2020, manymanuals.com. All rights reserved. | 0.883 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals