Runco Q-750d Ultra Series Specifications Page 94
- Page / 134
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Operation
78 Q-750d Ultra Series Installation/Operation Manual
PRE
L
IMINAR
Y
• Error Notification: To have the DHD Controller send a message to the destination
e-mail address when a “DHD Error” or “Display Error” occurs, select Error
Notification from the E-Mail Notification menu and set it to On.
• Error Notification to Runco: To have the DHD Controller send an e-mail message
to Runco Customer Support when a “DHD Error” or “Display Error” occurs, select
Error Notification to Runco from the E-Mail Notification menu and set it to On.
• Periodic Service Notification: You can have the the DHD Controller send periodic
reminders via e-mail to perform regular maintenance tasks. To do this:
1. Select Periodic Service Notification from the E-Mail Notification menu.
2. Highlight Enable and press ENTER.
3. Highlight On and press ENTER.
4. Press MENU.
5. Highlight Timer and press ENTER.
6. Press or to set the notification interval in months. The range is from 1 to
255 inclusive; the default is 12 months.
7. Press MENU.
• Lamp Life Notification: To have the DHD Controller send a message to the
destination e-mail address when the lamp hour counter reaches a certain threshold,
select Lamp Life Notification from the E-Mail Notification menu. Then:
1. Highlight Enable and press ENTER.
2. Highlight On and press ENTER.
3. Press MENU.
4. Highlight Lamp Hours and press ENTER.
5. Press or to set the notification threshold in hours. The range is from 100 to
10,000 hours; the default is 1,000 hours.
6. Press MENU.
• Customer Information: Select Customer Information from the E-Mail Notification
menu to supply this information to the DHD Controller, which includes it in all e-mail
notification messages. Six lines (up to 30 characters per line) of text are provided;
use them however you wish.
1. Press or repeatedly to select a line of text to edit.
2. Press ENTER.
3. Press or repeatedly to set the highlighted character.
4. Press (or ) to select the next (or previous) character. Use the and
buttons to change it.
5. Press ENTER when you have finished editing that line of text.
6. Repeat Steps 1 through 5 for each line of text you want to edit.
7. Press MENU when you have finished entering customer information.
• E-Mail Calibration Data: To have the DHD Controller collect all calibration data,
attach it to a message and send it to the destination e-mail address, select E-Mail
Calibration Data from the E-Mail Notification menu. To confirm this action, select Ye
s
and press ENTER.
To cancel and return to the previous menu, select No.
- Q-750d Ultra Series 1
- Warranty 3
- Important Safety Instructions 7
- Compliance Information 8
- Table of Contents 11
- List of Figures 15
- 1. Introduction 17
- Using This Manual 18
- Description, Features 19
- Introduction 20
- 2. Controls and Functions 21
- Q-750d Ultra Rear 22
- DHD Controller Front 23
- DHD Controller Rear 24
- Controls and Functions 25
- Q-750d Ultra Remote 26
- Control Unit 26
- 3. Installation 29
- Quick Setup 30
- Installation 31
- Considerations 31
- Estimating Throw Distance 32
- Screen width (w) 32
- Ceiling Installation 34
- Floor Installation 34
- Installing the Primary 37
- Projection Lens 37
- Installing the Optional 40
- CineWide/AutoScope 40
- Lens Mount 40
- Mounting the Q-750d 46
- HDMI Out 47
- To Display 47
- DTV-Set-Top Box 50
- (DTV-STB) 50
- RGB Camcorder 51
- Figure 3-15 52
- Gaming Console 53
- Camcorder 53
- Audio Processor/ 54
- Switcher 54
- Secondary Display 54
- Control System 55
- AutoScope Lens Motor 56
- Turning on the Power 59
- Vertical 60
- Lens Shift 60
- Horizontal 60
- Adjusting the Image 61
- Geometry 61
- Installing and 63
- Adjusting the 63
- CineWide Anamorphic 63
- Too Far Right 65
- Too Far Left 65
- Correct position 65
- Too High 66
- Correct Lens Angle 66
- Incorrect Lens Angle 66
- Anamorphic Lens (Top View) 67
- 4. Operation 69
- 4:3 Image on 72
- 16:9 Display 72
- (Letterbox aspect ratio) 72
- 1080i HDTV Image 73
- 720p HDTV Image 73
- Below Black 75
- Off Crop Zoom 79
- Saturation 86
- Input Names 91
- Operation 100
- 6. External Control 103
- External Control 104
- Table 6-1. Serial Commands 105
- DBO R/W Yes -100 100 No 107
- DGO R/W Yes -100 100 No 107
- DRO R/W Yes -100 100 No 107
- IGO R/W Yes -32 32 No 109
- IBO R/W Yes -32 32 No 109
- IRO R/W Yes -32 32 No 110
- Using Discrete IR 118
- Using HDMI CEC 122
- Messages 122
- 7. Specifications 125
- DHD Controller 127
- Specifications 127
- Overall Dimensions – 129
- Q-750d Ultra 129
- Ultra/CineWide with 130
- AutoScope 130
- Supported Timings 131
- 020-1159-00 Rev. B 134
- November 2011 134
Related products and manuals for Data projectors Runco Q-750d Ultra Series
Data projectors Runco VX-8d Specifications
(104 pages)
(104 pages)
Data projectors Runco VX-2c Setup Guide
(36 pages)
(36 pages)
Data projectors Runco CL-500 User Manual
(32 pages)
(32 pages)
Data projectors Runco XP-103DHD Specifications
(126 pages)
(126 pages)
Data projectors Runco VX-4000d Specifications
(108 pages)
(108 pages)
Data projectors Runco VX-2i Specifications
(112 pages)
(112 pages)
© 2020, manymanuals.com. All rights reserved. | 6.103 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals